ماژول مبدل DC-DC کاهنده XL4015 به همراه نمایشگر
- برد رزبری پای - RASPBERRY PI
- بردهای کاربردی تحت سیستم عامل
- بردهای کاربردی صنعتی
- تجهیزات الکترونیک
- تجهیزات جانبی
- تغذیه سوئیچینگ صنعتی-آداپتور-منبع تغذیه
- جعبه - کیس های مدار و برد
- دستگاه کنترل پیامک
- ماژول ها
- ISM Band
- LCD
- درایور موتور
- دوربین
- ماژول اثر انگشت
- ماژول دما و رطوبت
- ماژول سنسور گاز
- ماژول های GSM/GPS/GPRS
- ماژول های RFID
- ماژول های آلتراسونیک
- ماژول های بلوتوث
- ماژول های تایمر و پالس
- ماژول های تغذیه و ولتاژ
- ماژول های شبکه و WIFI
- ماژول های شتاب سنج و ژیروسکوپ
- ماژول های صوتی و آمپلی فایر
- ماژول های فرستنده و گیرنده
- ماژول های فشار
- ماژول های مبدل
- ماژول های پزشکی و ضربان قلب
- ماژول های کاربردی
- ماژول پرینتر
- موتورها
- پروگرامرها
- کتاب های آموزشی و کاربردی
- کیت های آموزشی
- بردهای آموزشی ARM , AVR , PIC , FPGA
- روباتیک
- آردوینو
- سنسورها
- LED
- ریموت و کنترل کننده های صنعتی و کاربردی
- آنتن ها
- قطعات پروازی و ربات های پرنده
سبد خرید شما خالی است !
توضیحات محصول
ماژول مبدل DC-DC کاهنده XL4015 به همراه نمایشگر
ماژول مبدل کاهنده DC به DC با
آی سی XL4015E1 دارای قابلیت تنظیم
جریان و ولتاژ خروجی بوده و دارای بازدهی ۹۶ درصد می باشد. همچنین دارای محافظت در
مقابل افزایش دما، اتصال کوتاه و پلاریته معکوس ورودی است. جریان خروجی تا ۵ آمپر،
ولتاژ ورودی ۵ تا ۳۶ ولت و ولتاژ خروجی ۱٫۲۵ تا ۳۲ ولت می باشد.
مشخصات
ولتاژ ورودی : 5 ولت
الی 38 ولت
ولتاژ خروجی : 1.25 الی 36 ولت
جریان خروجی : حداکثر 5 آمپر (در صورت استفاده ازهیت سینک )
امکان کنترل ولتاژ خروجی
دارای نمایشگر سگمنت جهت نمایش ولتاژ
قابلیت حفاظت در برابر ولتاژ معکوس
توان خروجی: حداکثر 75 وات
حفاظت از اتصال معکوس ورودی : بله
حفاظت از اتصال کوتاه
ریپل پایین ولتاژ خروجی با وجود مدار فیلتر LC
فرکانس کاری: 180 کیلوهرتز
Introduction
The DC-DC Adjustable Step Down Converter
Module has large power, high efficiency, low-ripple. With power indicator,
on-board voltmeter. The voltmeter can calibrate automatically. The measure can
be changed between input and output voltage, with indicator. The voltmeter can
also be shutdown. The board uses connection terminal for easy wiring.
Built in thermal shutdown function
Built in current limit function
Built in output short protection function
Specification
Better than 2596, easy to 4A 50W, up to 75W adding
heat sink
Input voltage: 4V ~ 38V (not more than 38V)
Output voltage: 1.25V ~ 36V (adjustable)
Output current: 0A ~ 5A (recommended below 4.5A)
Output power: recommended use below 75W (add heat sink when more than 50W)
Operating temperature: -40°C ~ +85°C
Operating frequency: 180KHz
Conversion efficiency: Up to 96% (based on input and output voltage, current,
pressure)
Voltmeter range: 0V ~ 40V
Voltmeter error: ±0.1V (NOTE: To ensure the accuracy, keep the input above
4.5V)
Load regulation: S (I) ≤0.8%
Voltage regulation rate: S (u) ≤0.8%
Power indicator: Yes
Short circuit protection: Yes (limit current 8A)
Over temperature protection: Yes (shutdown output automatically after over
temperature)
Input Reverse Polarity Protection: None (cascade high current diode if
required)
Wiring: IN+/- Input, OUT+/- Output
Voltmeter calibration method
1. Onboard voltmeter shows that the output
voltage, long press the right button 2 seconds to loosen, voltmeter, and the
output voltage indicator light [OUT] synchronous flash, at this time into the
output voltage regulation mode; Similarly, when the input voltage IN the
voltmeter display, long press the right button 2 seconds to loosen, voltmeter,
and the input voltage indicator light [IN] synchronous flash, at this time into
the input voltage adjustment mode.
2. Light touch button on the right side, the voltage value is adding up a unit;
Press the left button, minus a unit; Due to a unit of voltage is less than 0.1
V, so you need to press the 1-5 consecutive can see the voltmeter change 0.1 V,
the concrete continuous button several times depends on the current display
voltage, current shows that the higher the voltage, the fewer the number of
press.
3. After the voltage adjustment, long press the right button for 2 seconds,
release, to exit the output voltage calibration mode, all the parameters set to
automatically power down saving.
The DC/DC buck module applications the input voltage is higher than the output
voltage of the buck field, such as battery, power transformer, DIY adjustable
regulated power supply, LCD Monitor and LCD TV, portable instrument power
supply, telecom/networking equipment, 24V vehicle notebook power supply,
industrial equipment buck. 12V buck to 3.3V, 12V buck to 5V, 24V buck to 5V,
24V buck to 12V, 36V buck to 24V etc.